May 17, 2018

Computer Hard Drive Clock

3 comments

If you've ever scratched your head and wondered what you can do with old computer parts, this is the tutorial for you! We took an old computer apart and upcycled the hard drive into a one-of-a-kind clock!

 

Before you can take apart a hard drive, it’s good to know the name of the parts. If you get stuck, refer back to this diagram. Not marked below is the motor which is hidden within the spindle hub.

Don’t forget to wipe the drive clean of data before upcycling it. Apart from the hard drive, you'll need safety goggles, torx bits, a screw gun, punch, vise, drill bits, hammer and clock kit.

If you’re buying eye protection for this project, choose the pair that provides you with a full seal around the face. The top pair of goggles shown below is is better for this project (as compared to the one underneath it) because they’ll prevent flying bits of metal from all angles from reaching your eyes).

I used a clock mechanism that I salvaged from a clock I got for free at a garage sale. If you have to buy a kit, get one that has a 3/4″ shaft and short clock arms (like the one shown above). If you’re upcyling one  with long arms, you can probably still use it but will have to cut the arms to fit within the platter.

 

Torx bits are made for a screw head that is shaped like a 6-point star. I used a #8 Torx bit. I found that the #8 worked for every screw in this particular hard drive, but I have had instances where I needed a smaller bit too (i.e. for the motor).

Salvage the hard drive from an old computer:

Start by removing the circuit board and membrane on the back to clean it up:

Turn the hard drive over and remove the screws from the front of the case.

If you find that you can’t remove the front plate, it could be because there are at least one or more screws hiding underneath the label. You can feel for it and use an X-acto knife to score an ‘X’ to cut it open.

Open the case to reveal the shiny mirror-like platter. Remove all the screws around the spindle (there were six). Save the screws for later; you’ll need them when you reassemble.

Remove the collar and ring which will free up the platter and set them aside for later also.

Just a few turns to the left and the actuator arm popped up enough that the platter could slide out.

With the screw loosened, slide the platter out from the back side. By the way, when you’re handling the platter, try not to get finger prints on the shiny surface. If you do, it’s a pain to clean them off. Hold the platter on the edges.

The motor has to be removed next and then drilled out to accept the clock mechanism.

Watch this how-to video (and subscribe while you're at it), then head to my blog for the step-by-step instructions and photos on how to remove the motor, drill it out and assemble the clock mechanism: http://birdzofafeather.ca/craft-rehab/computer-hard-drive-clock/

If you like, you can add clock numbers onto the face, but I prefer it just the way it is. You can either hang your clock on the wall using the tab on the clock mechanism, or add a bracket so it can sit on a desk.

We hope you enjoyed this project! For more upcycle projects, check out our site: http://birdzofafeather.ca

May 17, 2018Edited: May 17, 2018

This is so cool!!! Well done... We will be sharing via the network very soon ;) !!! And if you have some more nice recycled ideas like it, feel free to share with us...

May 17, 2018

Thanks DIY@ATC for the share! I do have more recycle ideas to come :)

May 17, 2018

Looking forward to see and share them with our community!!!

New Posts
  • Hi guys , in this new video I show you how I have restored and soundproofed an old noisy and anti-aesthetic metal door. With a few euros and a couple of hours of work you can recover an old door. At the moment I will leave it raw but if you wish you can paint it and finish it.
  • Hello every one , i'm new here and this is what i do. There are plenty ideas like this in my youtube channel(DIY Tips with MG) Don't hesitate to visit it 😊😉
  • Hi guys, Today we are going to do a quick review of this very useful parkside product the Disc sander pTSG 140 A1. As you can see on the box they provide most of the information in several languages. A short video to give you more details: Let me know what you think in the comment below!!! Mr ATC for another idea of housing Youtube Facebook Twitter Instagram Would you like to support ATC for more sustainable consumption patterns? Take part of the 1 reservation = 1 tree planted program, book here and share: Hotels Flights Holidays homes Car rentals Did you like this article? Register now and for free to be informed of new and up-to-date news articles. Newsletter... You like, you care, you share!
ATC DIY Community
ATC Design
wormerweg 4G-112, 1311 XB Almere
the Netherlands
KvK: 72065281
BTW: NL263226773B01
Services
Support & Contact
Terms & conditions 
Privacy policy
Blogger traffic Program
 
Free 3D plan